Search results
- Dictionaryprobing/ˈprōbiNG/
adjective
- 1. inquiring closely into something; searching: "she asks some probing questions"
Powered by Oxford Dictionaries
PROBING_MARGIN_LEFT PROBING_MARGIN_RIGHT PROBING_MARGIN_FRONT PROBING_MARGIN_BACK Note that in Marlin 1.1.x the boundaries are set in absolute positions while in Marlin 2.0.x it is described in offset values from the bed edge.
Dec 3, 2020 · 1. PROBING_MARGIN and MESH_INSET make the effective probing area smaller, so if you want to have more area, you should reduce the value of these constants. As of Marlin 2.x, the probing area isn't defined directly by the firmware configuration settings, but calculated, based on the probe offset settings. The constants you mention are reducing ...
As you have not posted a bed size, an assumed X bed size of 220 mm would mean that the maximum probing distance for X (i.e. RIGHT_PROBE_BED_POSITION) of 220 - 41 = 179 mm. In your case -41 mm would take it to the edge, so 30 mm extra would make it symmetrical: #define LEFT_PROBE_BED_POSITION 30. #define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - 41 ...
Feb 9, 2020 · to enable bi-linear levelling, you should remove the comment characters before constant #define AUTO_BED_LEVELING_BILINEAR: #define AUTO_BED_LEVELING_BILINEAR. Definition of the grid is done by specifying how many point you want to have using constants GRID_MAX_POINTS_X and GRID_MAX_POINTS_Y:
Jan 6, 2020 · Use M48 to verify accuracy. #define EZABL_FASTPROBE // Superfast probing - Only works with the EZABL Pro Sensors // DO NOTE: Not all machines will work with the fast probe enabled. Use M48 to verify accuracy and make sure the Z isn't binding with the high speeds. //#define EZABL_SUPERFASTPROBE
May 1, 2020 · I have #define PROBING_MARGIN_FRONT (PROBING_MARGIN - PROBE_Y_OFFSET_FROM_EXTRUDER) and #define PROBING_MARGIN_BACK 0. Unfortunately my attempt to set PROBING_MARGIN_BACK to negative had failed (there is a compile-time check preventing that).
Jul 15, 2020 · 0. Homing and mesh probing are 2 separate actions, by setting #define MULTIPLE_PROBING to 3, you inherently create 3 slow probing points for the mesh probing (not the homing probing), with 2 you get a fast/slow probing action. Everything is possible, but, that means that you need to dig into the sources; not changing the configuration constants.
For more piece of mind during homing, you may use the Z_MIN_PROBE_ENDSTOP feature with a normally-closed limit switch wired to an available pin on your control board: // Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine. // With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
Dec 18, 2021 · Uncommented #define Z_MIN_PROBE_REPEATABILITY_TEST. I want to test my 3DTouch and uncommenting allows the use of M48 to test it. Uncommented #define PROBING_FANS_OFF, #define PROBING_ESTEPPERS_OFF, #define PROBING_STEPPERS_OFF, #define DELAY_BEFORE_PROBING 200. The documentation this may improve probing results. I'm all in.
Jan 4, 2022 · Uncommented #define Z_MIN_PROBE_REPEATABILITY_TEST. I want to test my 3DTouch and uncommenting allows the use of M48 to test it. Uncommented #define PROBING_FANS_OFF, #define PROBING_ESTEPPERS_OFF, #define PROBING_STEPPERS_OFF, #define DELAY_BEFORE_PROBING 200. The documentation this may improve probing results. I'm all in.
